View HMC400MS806_4138384.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HMC400MS8 / 400MS8E
v02.0705
HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz
Designer's Kit Available
Typical Applications
High Dynamic Range Infrastructure: * GSM, GPRS & EDGE
Features
+35 dBm Input IP3 Conversion Loss: 8.8 dB No External Components Ultra Small MSOP Package: 14.8mm2 Included in the HMC-DK003 Designer's Kit
7
MIXERS - SMT
* CDMA & W-CDMA * Cable Modem Termination Systems
Functional Diagram
General Description
The HMC400MS8 & HMC400MS8E are high dynamic range passive MMIC mixers in plastic surface mount 8 lead Mini Small Outline Packages (MSOP) covering 1.7 to 2.2 GHz. Excellent input IP3 performance of +36 dBm for down conversion and +29 dBm for up conversion is provided for 2.5G & 3G GSM/CDMA based UMTS or PCS applications at an LO drive of +17dBm. With a 1dB compression of +21 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 8.5dB typical and LO isolations are maintained at 22 to 33 dB. This miniature singleended monolithic GaAs FET mixer does not require any external components or bias. The 50 to 300 MHz IF frequency response will satisfy many UMTS/PCS transmit or receive frequency plans configured for low side LO. The HMC400MS8 & HMC400MS8E input IP3 performance coupled with its high P1dB rivals traditional active FET mixers while offering a much smaller 14.8mm2 standard IC footprint and no DC bias.
Electrical Specifications, TA = +25C, LO = +17dBm, IF = 200 MHz*
Parameter Frequency Range, RF Frequency Range, LO Frequency Range, IF Conversion Loss Noise Figure (SSB) LO to RF Isolation LO to IF Isolation IP3 (Input) 1 dB Gain Compression (Input) LO Input Drive Level (Typical) 29 16 30 18 Min. Typ. 1.7 - 1.8 1.4 - 1.75 DC - 300 9 9 33 20 34 21 +16 to +18 11 11 24 17 32 18 Max. Min. Typ. 1.8 - 2.0 1.5 - 1.95 DC - 300 8.8 8.8 30 22 36 21 +16 to +18 10.5 10.5 20 19 28 18 Max. Min. Typ. 2.0 - 2.2 1.7 - 2.15 DC - 300 8.8 8.8 25 25 32 22 +16 to +18 10.5 10.5 Max. Units GHz GHz MHz dB dB dB dB dBm dBm dBm
*Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz.
7 - 272
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC400MS8 / 400MS8E
v02.0705
HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz
Conversion Gain vs. Temperature @ LO = +17 dBm
0
Isolation @ LO = +17 dBm
0
RF TO IF LO TO RF LO TO IF
CONVERSION GAIN (dB)
-5 ISOLATION (dB)
-10
7
MIXERS - SMT
7 - 273
-10
-20
-15
+ 25C + 85C - 40C
-30
-20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3
-40 1.7 1.8 1.9 2 2.1 FREQUENCY (GHz) 2.2 2.3
Conversion Gain vs. LO Drive
0
Return Loss @ LO = +17 dBm
0 -5 RETURN LOSS (dB)
CONVERSION GAIN (dB)
-5
-10 -15 -20 -25 -30
RF LO
-10
-15
LO = +15 dBm LO = +16 dBm LO = +17 dBm LO = +19 dBm
-20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3
1.7
1.8
1.9 2 2.1 RF FREQUENCY (GHz)
2.2
2.3
Upconverter Performance Conversion Gain @ LO = +17 dBm
0
If Bandwidth @ LO = +17 dBm
0
CONVERSION GAIN (dB)
-5 RESPONSE (dB)
-5
-10
-10
-15
-15
CONVERSION GAIN RETURN LOSS
-20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3
-20 50 100 150 200 250 300 350 IF FREQUENCY (MHz) 400 450 500
*Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC400MS8 / 400MS8E
v02.0705
HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz
Input IP3 vs. Temperature, LO = +17 dBm
40
Input IP3 vs. IF Frequency, RF = 1.75 GHz
40
INPUT IP3 (dBm)
30
INPUT IP3 (dBm)
7
MIXERS - SMT
35
35
30
25
LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm
25
+ 25C + 85C - 40C
20 60 90 120 150 180 210 240 IF FREQUENCY (MHz) 270 300
20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3
Input IP3 vs. IF Frequency, RF = 1.95 GHz
40
Input IP3 vs. LO Drive
40
35 INPUT IP3 (dBm) INPUT IP3 (dBm)
35
30
30
25
LO = +15 dBm LO = +16 dBm LO = +17 dBm LO = +19 dBm
25
+ 15dBm + 16dBm + 17dBm + 19dBm
20 60 90 120 150 180 210 240 IF FREQUENCY (MHz) 270 300
20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3
Input IP3 vs. IF Frequency, RF = 2.15 GHz
40
Upconverter IP3 vs. LO Drive, IF = 200 MHz
40
35 INPUT IP3 (dBm) INPUT IP3 (dBm)
35
LO = +15 dBm LO = +16 dBm LO = +17 dBm LO = +19 dBm
30
30
25
LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm
25
20 60 90 120 150 180 210 240 IF FREQUENCY (MHz) 270 300
20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3
*Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz.
7 - 274
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC400MS8 / 400MS8E
v02.0705
HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz
Input IP2 vs. Temperature @ LO = +17 dBm
45
Input IP2 vs. LO Drive @ LO = +17 dBm
45
40 INPUT IP2 (dBm) INPUT IP2 (dBm)
40
35
35
7
+ 15 dBm + 16 dBm + 17 dBm + 19 dBm
30
+ 25C + 85C - 40C
30
25
25
20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3
20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3
Input P1dB vs. Temperature @ LO = +17 dBm
25 24 23 INPUT P1dB (dBm) 22 21 20 19 18 17 16 15 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3
+ 25C + 85C - 40C
MxN Spurious Outputs
nLO mRF 0 1 2 3 4 0 xx 9 71 79 77 1 -11 0 70 80 80 2 7 24 49 80 80 3 4 31 58 79 79 4 8 27 64 77 80
RF Freq = 2 GHz @ -10 dBm LO Freq = 1.8 GHz @ +17 dBm All values in dBc relative to the IF output power.
Harmonics of LO
nLO Spur @ RF Port LO Freq (GHz) 1.4 1.55 1.7 1.85 2 2.15 1 42 33 29 26 24 21 2 26 25 29 31 36 38 3 56 56 49 44 44 43 4 46 53 50 53 48 49
Absolute Maximum Ratings
RF/IF Input LO Drive Storage Temperature Operating Temperature IF DC Current +27 dBm +27 dBm -65 to +150 C -40 to +85 C 40 mA
ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS
LO = +17 dBm All values are in dBc below input LO level @ RF port.
*Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
7 - 275
MIXERS - SMT
HMC400MS8 / 400MS8E
v02.0705
HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz
Outline Drawing
7
MIXERS - SMT
NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND.
Package Information
Part Number HMC400MS8 HMC400MS8E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1
[1]
Package Marking [3] H400 XXXX H400 XXXX
[2]
[1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX
7 - 276
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC400MS8 / 400MS8E
v02.0705
HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz
Pin Descriptions
Pin Number Function Description Interface Schematic
1
LO
This pin is AC coupled & matched to 50 Ohms from 1.4 to 2.2 GHz. Blocking capacitors are required if line potential is not equal to 0V.
7
MIXERS - SMT
7 - 277
2, 4
N/C
Not connected.
3, 6, 7
GND
This pin must be connected to RF ground. This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of capacitor to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result.
5
IF Port
8
RF Port
This pin is DC coupled & matched to 50 Ohm from 1.7 to 2.2 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC400MS8 / 400MS8E
v02.0705
HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz
Evaluation PCB
7
MIXERS - SMT
List of Materials for Evaluation PCB 101830
Item J1 - J3 U1 PCB [2] Description PCB Mount SMA RF Connector HMC400MS8 / HMC400MS8E Mixer 101828 Eval Board
[1]
[1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350
The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
7 - 278
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC400MS8 / 400MS8E
v02.0705
HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz
Notes:
7
MIXERS - SMT
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
7 - 279

▲Up To Search▲

Price & Availability of HMC400MS806

	To Download HMC400MS806 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .